1/17/2023 0 Comments Windows port map![]() ![]() Third party names may be trademarks of their respective owners. © 2015-2022 Pure Storage® (“Pure”), Portworx® and associated its trademarks can be found here as and its virtual patent marking program can be found here. Setup iSCSI on Windows Server with Windows PowerShell.Setup iSCSI on Windows Server 2008 R R2 (Service Pack 1).Name Time Initiator WWN Initiator IQN Target Target WWN Failover I/O Count I/O Relative to Max The host can also be monitored using the Purity CLI with the below purehost monitor -balance The results of the plumbing test should generate similar output as below. To learn how to set up a drive letter for a newly connected volume see Working with Volumes on a Windows Server Host. The in the command line should be the drive letter of the newly connected volume. Running diskspd with the below example command line will generate I/O to evaluate connectivity. The use case mentioned here is to simply test the connectivity to the FlashArray. PS >Set-PfaInterfaceMtu -Array $FlashArray -Name 'ct1.eth6' -Mtu 9000ĭISKSPD is not recommended for performance testing. PS >Set-PfaInterfaceMtu -Array $FlashArray -Name 'ct0.eth7' -Mtu 9000 PS >Set-PfaInterfaceMtu -Array $FlashArray -Name 'ct0.eth6' -Mtu 9000 PS > Get-PfaNetworkInterfaces -Array $FlashArray | Format-Table -AutoSize PS >Get-PfaNetworkInterfaces -Array $FlashArray | Format-Table -AutoSize PS >$FlashArray = New-PfaArray -EndPoint 10.21.201.57 -Credentials (Get-Credential) -IgnoreCertificateError Change the MTU size and click on Apply.Find the iSCSI Network interfaces and click on the Edit icon located at the end of the row.If the deployed switches in the fabric support changing the Maximum Transmission Unit (MTU) from 1500 to 9000 (referred to as Jumbo Frames), this can be accomplished using the FlashArray Management GUI, or by running the Windows PowerShell cmdlets from the Pure Storage PowerShell SDK. The Host Port Connectivity should show Redundant connections. Open up the FlashArray Management interface, click the System tab, click Connections, click Host Connections, and select the host that was just configured. After completing the setup of the Initiator IPs and Target Portal IPs, click the Favorite Targets tab and all of the configured paths should be visible.ġ2. Repeat Step 9 for all of the Initiator IPs and map to their appropriate Target portal IP.ġ1. Select the Target portal IP from the dropdown that will map to the Initiator IP. Select the appropriate IP Address from the Initiator IP dropdown. Click Enable multi-path then click Advanced. button.ġ0. In the Advanced Settings dialog select the Microsoft iSCSI Initiator from the Local adapter dropdown. If the host is connected to less than eight (8) paths, additional sessions can be configured going to the same target ports.ĩ. A session is normally created for every target port where a host is connected. Now the new host, Server01, is connected to the new volume, iSCSI-TestVolume, with the host port IQN set to :server01.īest Practice: For best performance out of a single host, eight (8) iSCSI sessions are recommended.Select the checkbox next to the iSCSI-TestVolume (or whatever volume name was created), then click Connect. The Connect Volumes to Host dialog will open.After creating the new volume click the elipsys in the Connected Volumes section and then select Connect.For this example the name iSCSI-TestVolume with a size of 500GB is being used. Click on the + in the Volumes section to create a volume.Enter the IQN from the previous section then click Add. The Configure iSCSI IQNs dialog box will open.Select the newly created host, Server01, then click the Ellipsis on the top right, then click Configure IQNs.Click on the + in the Hosts section and select Create Host. ![]() Open the Pure Storage FlashArray Management interface and log into the FlashArray.if a volume is not connected, you will receive an Authorization Failure. Connecting a volume to a configured iSCSI host on the Pure Storage FlashArray is required before configuring MSiSCSI. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |